12 Best Ways on How to Apply Disinfection Coating on Office Telephones – Telephones that are used in the office serve as a medium of communication between employees and their clients.
To maintain maximum hygiene, surfaces of office telephones need to be disinfected frequently. As they serve as a medium of transmission for infections from one person to another. People have found that most people stop using tissues after blowing their noses on them because they reuse these dirty tissues on the office telephone receivers.
The following list enumerates 10 ways on how to apply disinfection coating on telephones:
One of the easiest ways to apply disinfection coating on telephones is to first use a cotton swab dipped in alcohol. You can do this by dipping the cotton swabs into 70% isopropyl alcohol and applying it on the receiver’s surface until it is dry. After doing this, simply wipe out any excess liquid with tissue paper or other absorbent materials.
Another way to apply disinfection coating on office telephones is to mix 0.5 ounces of bleach solution (one-part bleach plus nine parts water) with two ounces of warm water (the ratio should be one ounce each). After dissolving the mixture, spray it directly onto telephone receivers using aerosol sprays for at least 10 seconds. Wait for 30 seconds before wiping it off with a clean cloth or damp sponge.
A third way of disinfecting office telephone receivers is by using disinfectant wipes. To do this, moisten the wipe with the disinfectant and then rub it all over the receiver’s surface. Leave it on for about 10 seconds before wiping it off with a dry cloth or tissue paper.
Another way to disinfect telephone receivers is by using Lysol liquid. First, spray the liquid onto a clean cloth and then wipe it all over the telephone receiver’s surface until it gets soaked. Let it sit for about 10 minutes before wiping it off with a clean cloth.
The other best way to apply disinfection coating on telephones is by mixing one part bleach and 10 parts detergent solution together in a spray bottle. After doing this, spray the entire surface of telephone receivers using aerosol sprays for 20 seconds before wiping it dry with a clean cloth or tissue paper.
One way of disinfecting office telephone receivers is by wetting the disinfectant wipes with water and then applying them on the receiver’s surface until its surface gets moistened all over. After that, simply wipe out any excess liquid from phone surfaces before allowing them to air dry for 15 minutes.
Another way of disinfecting office telephone receivers is through the use of Lysol wipes. To do this, moisten a clean cloth with Lysol liquid before applying it to the receiver’s surface until it becomes wet. Let the solution sit for 30 seconds before wiping it dry with a clean cloth or tissue paper.
By wetting the disinfectant wipes with water, you can apply it on the receiver’s surface until its surface gets moistened all over. After that, simply wipe out any excess liquid from phone surfaces before allowing them to air dry for 30 minutes.
Besides using cotton swabs dipped in alcohol, one can also easily disinfect an office telephone receiver by first using a bit of rubbing alcohol on a piece of tissue paper or paper towel and then proceeding to wipe the entire surface until no more liquid remains. After that, simply allow the phone surfaces to dry naturally without wiping them.
One can also disinfect office telephone receivers by spraying them with 70% isopropyl alcohol for 20 seconds before allowing the surfaces to dry naturally. This entire process should take about three minutes or more, depending on how large the phone is and what kind of surface it has (copper, gold, silver, etc.).
The other way of applying disinfection coating on telephones is through a baking soda and distilled water mixture that will cause a paste consistency.
For this method to work properly, moisten a clean cloth with pure distilled water before adding two teaspoons of baking soda, followed by mixing them until they are thoroughly blended. Using this homemade mixture, rub it on telephone receivers before allowing the surfaces to dry naturally for 10 minutes.
One can also disinfect office telephone receivers by using a 70% isopropyl alcohol solution or spray. To do this, spray the entire surface of the phone for 20 seconds before wiping it off with a clean cloth or tissue paper.
Instead of using alcohol solution or spray, you can also disinfect office telephone receivers by using a mixture of pure distilled water and rubbing alcohol in equal parts or ratios. For this method to work properly, moisten a clean cloth with the solution before wiping it all over the entire surface of the phone for 30 seconds before wiping it dry with a clean cotton cloth or tissue paper.
By doing these methods, you are sure that your office telephone receiver would be free from germs and other kinds of bacteria that will cause diseases if consumed or touched by human hands when talking on the phone.
The last way to apply disinfection coating on telephones is through the use of vodka. Dip a cotton swab in vodka and then rub it all over the receiver’s surface until no more liquid remains. Wait for five minutes before wiping it dry with a clean cloth or tissue paper. After disinfecting, allow the phone surfaces to air dry for 10 minutes.
There are different ways on how to disinfect office telephone receivers. Whichever method you choose, make sure that you are thorough in your disinfection process to help protect you and your colleagues from any germs or bacteria. Happy cleaning!